The esxcli storage nmp satp commands manage SATPs.

You can use these commands to perform the following tasks.

■

Retrieve and set configuration parameters.

■

Add and remove rules from the list of claim rules for a specified SATP.

■

Set the default PSP for a specified SATP.

■

List SATPs that are currently loaded into NMP and the associated claim rules.

The default SATP for an active-active FC array with a vendor and model not listed in the SATP rules is VMW_SATP_DEFAULT_AA.

Retrieving Information About SATPs

The esxcli storage nmp satp list command lists the SATPs that are currently available to the NMP system and displays information about those SATPs. This command supports no options and displays information about these SATPs. 

esxcli <conn_options> storage nmp satp list

The rule list command lists the claim rules for SATPs. 

esxcli <conn_options> storage nmp satp rule list
Adding SATP Rules

Claim rules specify that a storage device that uses a certain driver or transport or has a certain vendor or model should use a certain SATP. The esxcli storage nmp satp rule add command adds a rule that performs such a mapping to the list of claim rules. The options you specify define the rule. For example, the following command specifies that if a path has vendor VMWARE and model Virtual, the PSA assigns it to the VMW_SATP_LOCAL SATP. 

esxcli <conn_options> storage nmp satp rule add --satp="VMW_SATP_LOCAL" --vendor="VMWARE" --model="Virtual" --description="VMware virtual disk"

Option

Description

--driver

-D

Driver string to set when adding the SATP claim rule.

--device

-d

Device to set when adding SATP claim rules. Device rules are mutually exclusive with vendor/model and driver rules.

--force

-f

Force claim rules to ignore validity checks and install the rule even if checks fail.

--model

-M

Model string to set when adding the SATP claim rule. Can be the model name or a pattern ^mod*, which matches all devices that start with mod. That is, the pattern successfully matches mod1 and modz, but not mymod1.

The command supports the start/end (^) and wildcard (*) functionality but no other regular expressions.

--transport

-R

Transport string to set when adding the SATP claim rule. Describes the type of storage HBA, for example, iscsi or fc.

--vendor

-V

Vendor string to set when adding the SATP claim rule.

--satp

-s

SATP for which the rule is added.

--claim-option

-c

Claim option string to set when adding the SATP claim rule.

--description

-e

Description string to set when adding the SATP claim rule.

--option

-o

Option string to set when adding the SATP claim rule. Surround the option string in double quotes, and use a space, not a comma, when specifying more than one option. 

"enable_local enable_ssd"

--psp

-P

Default PSP for the SATP claim rule.

--psp-option

-O

PSP options for the SATP claim rule.

--type

-t

Set the claim type when adding a SATP claim rule.

The following examples illustrate adding SATP rules. Specify one of the options listed in Connection Options for vCLI Host Management Commands in place of <conn_options>.

■

Add an SATP rule that specifies that disks with vendor string VMWARE and model string Virtual should be added to VMW_SATP_LOCAL. 

esxcli <conn_options> storage nmp satp rule add --satp="VMW_SATP_LOCAL" --vendor="VMWARE" --model="Virtual" --description="VMware virtual disk"
■

Add an SATP rule that specifies that disks with the driver string somedriver should be added to VMW_SATP_LOCAL. 

esxcli <conn_options> storage nmp satp rule add --satp="VMW_SATP_LOCAL" --driver="somedriver"
■

Add a rule that specifies that all storage devices with vendor string ABC and a model name that starts with 120 should use VMW_SATP_DEFAULT_AA. 

esxcli <conn_options> storage nmp satp rule add --satp VMW_SATP_DEFAULT_AA --vendor="ABC" --model="^120*
Removing SATP Rules

The esxcli storage nmp satp rule remove command removes an existing SATP rule. The options you specify define the rule to remove. The options listed for Adding SATP Rules are supported.

The following example removes the rule that assigns devices with vendor string VMWARE and model string Virtual to VMW_SATP_LOCAL. 

esxcli <conn_options> storage nmp satp rule remove --satp="VMW_SATP_LOCAL" --vendor="VMWARE" --model="Virtual"
Retrieving and Setting SATP Configuration Parameters

The esxcli storage nmp satp generic deviceconfig get and esxcli storage nmp satp generic pathconfig get commands retrieve per-device or per-path SATP configuration parameters. You cannot retrieve paths or devices for all SATPs, you must retrieve the information one path or one device at a time.

Use the following command to retrieve per device or per path SATP configuration parameters, and to see whether you can set specific configuration parameters for a device or path.

For example, esxcli storage nmp satp generic deviceconfig get --device naa.xxx might return SATP VMW_SATP_LSI does not support device configuration. 

esxcli storage nmp satp generic pathconfig get -path vmhba1:C0:T0:L8 might return INIT,AVT OFF,v5.4,DUAL ACTIVE,ESX FAILOVER

The esxcli storage nmp satp generic deviceconfig set and esxcli storage nmp satp generic pathconfig set commands set configuration parameters for SATPs that are loaded into the system, if they support device configuration. You can set per-path or per-device SATP configuration parameters.

Important

The command passes the configuration string to the SATP associated with that device or path.

The configuration strings might vary by SATP. VMware supports a fixed set of configuration strings for a subset of its SATPs. The strings might change in future releases.

Options

Description

--config

-c

Configuration string to set for the path specified by --path or the device specified by --device.

You can set the configuration for the following SATPs.

■

VMW_SATP_ALUA_CX

■

VMW_SATP_ALUA

■

VMW_SATP_CX

■

VMW_SATP_INV

You can specify one of the following device configuration strings.

■

navireg_on – starts automatic registration of the device with Navisphere.

■

navireg_off – stops the automatic registration of the device.

■

ipfilter_on – stops the sending of the host name for Navisphere registration. Used if host is known as localhost.

■

ipfilter_off – enables the sending of the host name during Navisphere registration.

--device

-d

Device to set SATP configuration for. Not all SATPs support the setconfig option on devices.

--path

-p

Path to set SATP configuration for. Not all SATPs support the setconfig option on paths.

Run esxcli storage nmp device set --default --device=<device> to set the PSP for the specified device back to the default for the assigned SATP for this device.